I am a Mechanical engineer graduate from RNSIT, Bangalore. Currently doing master certification program in CFD from skill lync, Chennai.

I have done cerification courses in SOLIDWORKS, CATIA V5, ANSA and ANSYS.

#### Contact Info

Contact no: 9006401254

Email ID: [email protected]

### Comparing default shell properties with recommended properties through simulation in HyperView and plotting in HyperGraph LUV KUMAR · 2019-09-21 15:07:20

OBJECTIVE: To compare the results with base simulation and improved shell elements properties by performing energy, mass error checks, plotting graph in HyperGraph and animating in HyperView. SIMULATION 1: With default Shell Properties. Imported Element_Formulati Read more

### Cleaning Extracting Mid Surface and Meshing models in Hypermesh LUV KUMAR · 2019-09-20 05:08:03

OBJECTIVE: To clean the geometry, extract mid surface, mesh the extracted surface and assign thickness to given models. LINK TO HYPERMESH FILES https://drive.google.com/file/d/1Op9RLc8y85U2qtlLyBNh5GYCglVHuNqN/view   PROCEDURE: Model was imported and to see Read more

### 2D 3D Mesh in HyperMesh and Performing animation using Radioss as solver LUV KUMAR · 2019-09-20 05:05:54

OBJECTIVE: Surface mesh and volume mesh generation on given housing and arm bracket model. LINK TO HYPER MESH RADIOSS FILES: https://drive.google.com/file/d/1h0tOn4b9e9EDoVFqaGuKCjnWRgrHxUvL/view 3D MESHING: 3D Elements should be used when all dimensions are compara Read more

### NEWTON RAPHSON METHOD LUV KUMAR · 2019-09-13 07:11:16

OBJECTIVE: To find minimum pressure using Newton-Raphson method PROGRAMMING EXPLAINED: Two functions are defined. f and fprime. These function are defined to calculate next iteration value using NR method. To calculate pressure values for different thickness, for a Read more

### File Parsing in Python LUV KUMAR · 2019-09-13 06:25:32

OBJECTIVE: To demonstate file parsing using Python. when we run the program, first thing appears is  to enter the filename,if we speicify correct name then we can see the rest output otherwise a message will show file not found. To store different properties li Read more

### SciPy Curve Fitting LUV KUMAR · 2019-09-12 14:32:22

OBJECTIVE: To curve fit given data using linear and cubic polynomial. For curve fitting, we imported curve_fit from scipy library. Defined two function, func and func1 which are used for fitting curve. Defined another function read_file to read temperature and cp v Read more

### SciPy curve fitting LUV KUMAR · 2019-09-12 14:31:46

OBJECTIVE: To curve fit given data using linear and cubic polynomial. For curve fitting, we imported curve_fit from scipy library. Defined two function, func and func1 which are used for fitting curve. Defined another function read_file to read temperature and cp v Read more

### Solving 2nd order ODE in Python using ODEINT LUV KUMAR · 2019-09-11 11:32:12

OBJECTIVE: Solving differential equation using ODEINT and simulating motion of pendulum using solution from ODE. Given ODE of 2nd order.   PROGRAMMING EXPLAINED: 1.To solve ODE of 2nd order, we have to convert above equation into two, single order ODE. (d(t Read more

### Constrained Optimization LUV KUMAR · 2019-09-11 09:34:15

OBJECTIVE: In this challenge, we will find minimum value of the given function which is constrained by other function. SOLUTION: Given: f(x,y)=5-(x-2)^2-2(y-1)^2 constrained to x+4y=3 Optimization: g(x,y)=5-(x-2)^2 -2(y-1)^2+lamda(x+4y-3) (partialg)/(p Read more

### OTTO CYCLE SIMULATOR USING PYTHON LUV KUMAR · 2019-09-11 04:49:03

OBJECTIVE: In this challenge, we will plot pressure-volume reationship for otto cycle by varying crank angle from 0-180degree. PROGRAMMING EXPLAINED: Initially we are provided with p1,t1 and t3. Rest values at state points are calculated using combined gas law form Read more